Basic Baby Quilt Tutorial

Here’s a quilt that is as simple as sewing a straight line. That’s right … no intricate piecing or quilting, just lots and lots of straight lines. This is a wonderful beginner project and a great way to get practice while actually sewing something wonderful!

I didn’t invent this style of quilting and the idea of sewing a bunch of strips together is nothing new either. It just happens to be one of my favorite ways to quilt! In fact, I love it so much {and want others to love it too} this isn’t the first time I’ve written a tutorial on the process. It seems however that each time I sit down to make one of these quilts, it comes out just a bit different than those in the past.

This should give you the basic idea of how to sew a basic baby quilt using all straight lines.

Basic {Straight Line} Baby Quilt Tutorial {by Knitty Bitties}
Fabric provided by: Riley Blake Designs

Finished size: 40″x 54″

Materials Needed::

Helpful Equipment::

  • Rotary Cutter
  • Cutting Mat
  • Walking Foot {for your sewing machine}

 

Step 1.
Cut strips of fabric for your quilt top. You will need to cut as follows::

Front Fabrics –

  • Main Fabric {A} – Cut {2} strips 5″
  • Main Fabric {B} – Cut {2} strips 8″
  • Accent Fabrics {C-F} – Cut {1} strip each 2.25″ / 3″ / 3.75″

Back Fabrics –

  • Print Fabric – Cut {2} strips 18″
  • Solid Fabric – Cut {1} strip 20″

All cuts are the full width of the fabric {selvage to selvage} by the above measurement.

Step 2.

Determine the layout you’d like for your strips. {For mine, I started with three different accent strips in varying widths, then one of my main fabric strips. I repeated this pattern (4) times.} Then, stack the strips in order with the top/beginning strip on the top of the pile.

Step 3.

Sew the strips together. Take the first strip and place it right side up. {You’ll notice one selvage edge usually has the pattern on it and the other edge has fabric/printing information. I like to keep the ends with the pattern all lined up on the left side.} Take the next strip and place it right side down, matching up the selvage edge on the left and the raw edge on the bottom. Pin the two fabrics together {I like to pin about 1″ from the edge so that I don’t have to remove my pins while I sew.} and sew using a 1/4 seam allowance (SA) with a small stitch length of 2.2-2.5. Back stitch at the beginning and ending of each seam. Press seam OPEN using steam to get a nice flat seam.

Step 3b.

Similar to step 3a, lay out your now pieced together strip right side up. Take the next strip and lay it right side down, again matching up the selvage edge on the left and the raw edges along the bottom. Pin the fabric together. This time you will sew from the bottom to the top. {The reason for this is that by switching directions, you’re less likely to get a ‘curve’ to your strips and will end up with a more square quilt top.} Press seams open.

Repeat Steps 3a & 3b for remaining strips, remembering to alternate the direction of your sewing.

Hurray, you’ve just made you’re self a quilt top! Pat yourself on the back, stretch, go grab a fresh iced tea and come back refreshed and ready to finish your quilt.

Step 4.

Time to trim up your quilt top. Lay one of your selvage edges on your cutting mat and line your ruler up with the most inset selvage edge {they may be varying lengths so you have to go with the shortest to get a straight edge}. Trim excess. You’ll have to adjust your quilt top several times on your cutting mat to trim the full length. Repeat on opposite edge. Your quilt top should be about 40″ wide by 54″ in length.

Step 5.
Preparing your backing. I didn’t have quite enough of the zig-zag fabric to cover the whole back, so I cut it in half and added a strip of solid fabric.You could just as easily use a solid cut of fabric {you would need 1 3/4 YD}.


Step 6.

Making your quilt ‘sandwich.’ Your sandwich is: your quilt back right side down, batting and then your quilt top right side up. There are several good tutorials on how to do this in greater detail. The larger your quilt the more accurate you need to be. Because this is a small quilt {and because I didn’t want to clean my floors} I am sandwiching my quilt on my ironing board table. Start with your quilt top down, then layer on your batting and then place your quilt top, making sure you have at least a 1.5″ border of the backing showing all around. {To make it easier to see my backing, I cut my batting so that it was just slightly bigger than the front piece, but smaller than the back.}

Iron all three layers and begin to pin in place using quilting pins {they look like curved safety pins}. Carefully shift all three layers on the ironing board and smooth everything out, iron and pin. Make sure you keep checking you have at least a 1.5″ border of your back fabric on all sides.

Step 7.

Let’s quilt! We’re going to do straight line quilting which is really no different than the way you sewed your strips together EXCEPT you’ll want to use a much longer stitch length {about 3.5} and you might need to tighten your tension a bit {I tighten mine by 1 on my machine}. Ideally, you will also want to use a ‘walking foot.’ A walking foot provides ‘feed dogs’ on top to help pull all layers through at the same rate. They make a walking foot for most machines, but it doesn’t always come standard. A quick search should give you an online resource. If your machine came with an extension table now would be the time to use that as well {not necessary, but it will make things easier.}

We’re going to first quilt on each side of the seams you sewed earlier when you sewed the strips together. Start by lining up your needle so that it is approx. 1/4″ to the right of your first seam. Back stitch at the beginning and end of each row. Stitch the whole width of the quilt, but DO NOT go past your quilt top. When you get to the end, sink your needle down, lift your foot and rotate your quilt so that you can stitch on the other side of the seam. Put your foot down, lift your needle and adjust so that again you’re stitching 1/4″ to the right of the seam. Continue stitching the rest of the quilt like this. I never cut threads until the very end, you should be able to just keep moving your quilt and lining up on the next seam.

You will notice that as you go back and forth, you’ll need to ‘roll’ your quilt sides to more easily fit it on your machine.

** Don’t forget to match your bobbin thread to your quilt back. In this case, I used a dark teal to match the solid fabric. I used a natural thread on top. **

** You will most likely run out of your bobbin thread a couple times during the quilting process. When this happens, simply snip the top thread and bottom thread, remove your quilt, reload your bobbin and get back to your ending spot. Go over a few of your stitches and make sure to back stitch before you continue quilting. **

** One of the best tips on quilting is to not let your quilt weight ‘drag’ down your stitching. Try to keep your quilt from pulling by keeping it on your lap or on your sewing table and not hanging off the side creating pull and drag. **

Step 8.

Trim the batting. Carefully go around the quilt and trim off JUST the batting. Be careful not to cut through the front or back of the quilt.


Step 9.

Trim the backing. You want to have a perfect 1″ border of your backing fabric all the way around your quilt. Using your ruler and rotary cutter, trim the backing to 1″ from the quilt top edge.

Step 10.

Cheater binding. I’m using the method I learned from Made by Rae‘s tutorial. It works beautifully and has a ‘professional’ looking finish. You can read Rae’s full tutorial and this post of mine for some helpful tips. Use quilt binding clips {which look like hair clips} to hold your binding in place. Stitch binding down using a 2.5 stitch length and stitching as close to the edge of the binding as you feel comfortable. When you get to a corner, sink your needle down and pivot your quilt and continue on the next side until you’re back to your starting point.

TA-DA! Snip your thread and you’ve got yourself a beautiful handmade quilt!

Riley Blake sweetly sponsored this tutorial by providing all of the fabric I used for the quilt. Links to specific fabrics used are included in the “Materials Needed” above. Thank you Riley Blake!!

Comments

  1. Bookminder@gmail.com says:

    The link to your post on binding doesn’t work. Is it still available?

    • Hi there,
      Thanks for letting me know. I updated it to reflect the direct link to its location on my ‘knittybittiessews’ domain. Let me know if you have any other troubles. XOXO

      • 2jennifer says:

        Thanks so much. I’m getting back into sewing after many years away from it and really appreciate your most helpful tips!

  2. Heather says:

    Made it! Loved the tutorial! It was my first quilt, and had a few little mistakes, but turned out pretty well. And I got all the supplies from Joann for about $18
    Thank you!

    • Thank you so much for taking time to let me know Heather! I love that!! I hope that this one gave you the confidence to tackle many more. The first time (of any pattern) is always a ‘learning’ time. So I always encourage people to at least try a second one to show of all those skills you gained! 😀 Happy Sewing!

  3. Thank you soon much for this tutorial! I made a blanket/quilt for my future daughter (she will be here in 6 weeks) and it turned out great! I used only 5 materials and one strip of each, so it has wider strips, but the batting I used was a good quality, it shouldn’t bunch between them, I hope. I had a hard time doing your step for sewing through the top layer, batting and backing, you suggested to be continuous and not cut the thread…but it was way too hard with my little machine to keep flipping the blanket aroubd., haha! It still turned out great :).

    • Thank you so much for taking the time to comment! I love getting feedback and I’m so happy you were able to make your daughter a quilt, that is the best!! I’d love a photo if you want to share!! XOXO

  4. Sheri says:

    Just used your tutorial to create a baby crib quilt. I did use separate binding though. The soon to be parents, who received the quilt, loved it. Thank you for putting your instructions on Pinterest.

  5. Hi! How come the measurements for the front fabrics totaled together don’t equal the measurements for the back fabric? It is six inches bigger in the front than the back as I total the amounts.

  6. Betty says:

    This quilt is super cute, and the tutorial was easy to follow. Thank you so much for the informative tutorial. I am wondering if after washing the quilt numerous times if the batting begins to bunch, since there does not appear to be any vertical quilting lines.

    • I haven’t personally kept any of the quilts I’ve made in this style, but I haven’t heard from family/friends of there being an issue. If you’re using high quality batting you shouldn’t have an issue.

  7. Looks great I lIke the idea of stripes layered in colours I was just going to use to fabric only

Trackbacks

  1. […] since it seemed to be the most beginner friendly. I really liked the simplicity of this Basic Baby Quilt Tutorial by Knitty Bitties. The instructions were insanely easy to follow PLUS she introduced me to […]

  2. […] pretty perfect! From there I chose some coordinating prints with a particular pattern in mind. The Basic Baby Quilt Tutorial by Knitty Bitties is my go-to quilt for a quick and easy project. This is my third time using the […]

Leave a Reply